A halogen-free label does not prove that a finished plastic compound meets a fire, smoke, or emissions requirement. You will be able to define the specification, compare mineral and phosphorus-based systems, set up a controlled processing trial, and verify performance at the actual wall thickness and production conditions.
Key takeaways
- Verify chlorine, bromine, and total-halogen limits in the finished compound.
- Select additives against the exact UL 94, LOI, or smoke test requirement.
- Check polymer compatibility, processing temperature, and the intended failure mode.
- Repeat trials at Delhi production conditions before approving the formulation.
What “halogen-free” means in a finished plastic compound
900 ppm chlorine and 900 ppm bromine are not limits you can verify by reading one additive’s SDS. In many electronics specifications, a halogen-free finished compound means no more than 900 ppm chlorine, no more than 900 ppm bromine, and no more than 1,500 ppm total halogens under an IEC 61249-2-21-style requirement.
Confirm whether the buyer’s clause applies to the finished compound, the additive, or combustion-gas emissions.
A formulation can contain a halogen-free flame retardant and still fail because another ingredient introduces chlorine or bromine. Check the complete recipe, including:
- Base resin and recycled content
- Pigments, masterbatch carriers, and optical brighteners
- Stabiliser packages, plasticisers, lubricants, and processing aids
- Glass-fibre sizing, coatings, adhesives, and contamination from shared equipment
Request a batch-specific declaration for each raw material, then test representative finished pellets after compounding. Combustion followed by ion chromatography is a suitable route for measuring chlorine and bromine at specification levels; use X-ray fluorescence as a screening tool, not as the sole release test.
Test multiple samples from the production lot because a clean certificate cannot reveal contamination introduced during blending or extrusion. Record the method, sample preparation, detection limit, and whether “total halogens” means chlorine plus bromine under the purchase specification. A product labelled halogen-free is not confirmed until the finished compound meets the agreed limits.
Match the additive to the fire and smoke test
A V-0 result only shows how a small specimen burns under UL 94 conditions. It does not prove low smoke or low heat release.
| Test | What it shows | What it does not replace |
|---|---|---|
| UL 94 V-0, V-1, V-2 | Vertical-burning behaviour, afterflame time, and flaming drips at a specified thickness and orientation | Smoke, oxygen demand, or full-product fire performance |
| ASTM D2863 LOI | The oxygen concentration needed to sustain burning | UL 94 or end-use fire testing |
| ASTM E662 | Specific optical smoke density during flaming and non-flaming exposure | Heat-release measurement |
| ISO 5659-2 smoke density chamber | Specific optical density of smoke under controlled exposure; “oxide” is not the measured result | Flame classification or heat release |
| ISO 5660-1 cone calorimetry | Heat-release rate, total heat released, ignition time, and related fire parameters | Smoke toxicity or UL 94 classification |
Treat each result as a different failure question. A compound can have a high ASTM D2863 LOI yet fail UL 94 because of long afterflame, melt flow, or flaming drips. A UL 94 V-0 specimen can still produce dense smoke in ASTM E662 or ISO 5659-2.
Test the target wall thickness and orientation: results can change when either changes. Specify smoke and gas hazards separately, because halogen-free chemistry does not mean smoke-free or non-toxic; oxygen-starved burning can still generate carbon monoxide, irritant phosphorus products, or corrosive condensates.
Choose chemistry by polymer, temperature, and failure mode
Processing temperature is the first filter. Aluminium trihydrate decomposition begins around 180–220 °C, while magnesium hydroxide decomposition occurs around 330–350 °C. Both rely on endothermic decomposition, water release, and dilution; high loading can reduce flow, toughness, elongation, and surface quality.
| Option | Best comparison point | When it applies |
|---|---|---|
| ATH | Early decomposition and high mineral loading | PP, rubber, and PVC smoke or flame control when melt temperatures remain below its release range |
| Magnesium hydroxide | Higher processing temperature versus loading penalty | PP and rubber processed near 330 °C; reject it when the required loading destroys impact strength or flow |
| Zinc borate | Synergy, char promotion, and afterglow reduction | Compare with hydroxides, phosphorus systems, or intumescents in PP, PVC, and rubber; excessive use raises density and can affect colour |
| APP intumescent | Char balance, not APP percentage alone | PP and selected polyamides when the package contains an intumescent acid source, carbon source, and blowing agent |
| Phosphorus chemistry | Resin-specific gas-phase or condensed-phase action | Compare aluminium diethylphosphinate in polyamide and PBT-type systems; screen the actual grade in PC/ABS and avoid assuming equal performance in PP |
| PVC formulation | Smoke and compatibility rather than halogen-free status | PVC already contains chlorine, so it cannot meet a strict halogen-free finished-compound requirement |
A stable intumescent char depends on acid-to-carbon balance, dispersion, melt viscosity, and wall thickness. In polyamide and PC/ABS, test phosphorus chemistry against glass fibre, pigments, and moisture; in rubber, compare residue integrity and afterglow. A V-0 result alone does not prove low smoke or low toxicity.
Build a trial that survives extrusion and injection moulding
Start with the target compound, not a neat-resin screening run: mineral hydroxide systems often need 40–60 wt% loading, where flow, tensile strength, elongation, impact resistance, screw torque, and surface finish become linked problems.
Set these controls before moulding:
- Dry nylon, PBT, APP-containing concentrates, and hygroscopic carriers to documented moisture limits. Use Karl Fischer moisture testing on incoming material and after monsoon storage; hopper temperature alone does not prove dryness.
- Define the masterbatch let-down ratio and verify additive content at that ratio by ash, elemental analysis, or an agreed method. A well-dispersed laboratory pellet can still hide an inaccurate production feeder.
- Complete feeder calibration with the actual pellet size, bulk density, and conveying arrangement. Record mass loss over a timed run rather than trusting the feeder display.
- Use a screw profile that provides distributive mixing without excessive shear or heat. Inspect pellets and moulded plaques for agglomerates, streaks, weak spots, and gloss variation.
- Keep residence time as short and consistent as the process allows. ATH releases water around 180–220 °C; magnesium hydroxide decomposes around 330–350 °C, while APP can hydrolyse and generate acidic species when wet.
- Log melt temperature, screw speed, back pressure, torque, injection pressure, cushion, and cycle time. Rising torque or pressure signals overload, poor feeding, or agglomeration.
Approve the trial only after tensile, impact, elongation, surface inspection, and fire testing on parts at the intended thickness. Compare results against the same loading and let-down ratio used in production.
Qualify the package under Delhi production conditions
Approve the package only after it passes both a humidity challenge and a production-scale trial; a dry laboratory sample can conceal feeder, dispersion, and storage failures.
1. Request the TDS, SDS, CoA, batch traceability, recommended loading, decomposition or activation temperature, and compatibility limits. Require particle size distribution, surface treatment, oil absorption, bulk density, moisture limit, and storage life; these values determine feeder accuracy, melt viscosity, and agglomeration risk.
2. For APP or hygroscopic carriers, require sealed-pack storage instructions and a moisture result from each batch. Set an incoming limit using Karl Fischer or an agreed equivalent, then retain sealed samples through Delhi’s humid season. Moisture can hydrolyse nylon or PBT, damage APP, and produce silver streaks, voids, or erratic flame results.
3. Expose the additive and concentrate to your documented hot-humid warehouse condition, recording temperature, relative humidity, and duration. Recheck caking, flow, moisture, colour, and dispersion after exposure; reject material that hardens in the bag or shifts the feeder rate.
4. Run the intended let-down ratio on the commercial extruder or injection machine, not only a supplier concentrate. Record feeder accuracy, screw torque and die pressure against the unfilled resin, melt temperature, residence time, strand appearance, and filter-screen build-up.
5. Verify additive content by ash, elemental analysis, or another agreed method. Test tensile strength, elongation, impact, UL 94, LOI, smoke, and gas results after the defined conditioning cycle.
Niknam Chemicals Pvt. Ltd should provide these batch-level records for the exact package and polymer grade being approved, not data from a different concentrate or loading.
Related products
![]() | Flame Retardant Filler FAM-501 Flame Retardant Filler FAM-501 FAM - 501 Flame Retardant filler FAM-501 is One Pack Flame Retardant & Smoke Suppressant developed for Plasticized PVC applications. View product → |
![]() | FAM-501 ABOUT FAM - 501 FAM-501 is One Pack Flame Retardant & Smoke Suppressant developed for Plasticized PVC applications. View product → |
Frequently asked questions
What does halogen-free mean in a finished plastic compound?
For many electronics specifications, it means no more than 900 ppm chlorine, 900 ppm bromine, and 1,500 ppm total halogens in the finished compound. Test the compound rather than relying on one additive’s SDS.
How do you match a flame-retardant additive to the required fire and smoke test?
Identify the required test first, such as UL 94, limiting oxygen index, glow-wire testing, or a smoke-density test. Then compare formulations using the same specimen thickness, conditioning, and test method.
How should you choose flame-retardant chemistry for a plastic?
Screen the additive against the polymer, melt-processing temperature, residence time, moisture sensitivity, and failure mode. A package that works in one resin can reduce impact strength, cause plate-out, or fail in another.
What should a processing trial include?
Run the additive through extrusion and injection moulding at production-relevant feed rate, melt temperature, screw speed, residence time, cooling, and mould conditions. Inspect dispersion, surface defects, torque, pressure, and final fire performance.
How do you qualify a flame-retardant package under Delhi production conditions?
Repeat testing with the actual resin, equipment, operators, ambient moisture, cooling water, and production cycle used in Delhi. Retain samples and record batch numbers, dosage, processing settings, and test results.
Related products
![]() | Aluminium Hydroxide ALUMINIUM HYDROXIDE is a Super Fine Precipitated Special ATH. View product → |
![]() | Aluminium Trihydrate (ATH) is a very finely grounded product having a uniform and controlled particle size distribution. View product → |
![]() | Zinc Borate ZINC BORATE is a highly effective multifunctional flame retardant synergist being used as a flame retardant and smoke suppressant in a wide range of... View product → |
![]() | Magnesium Hydroxide MAGNESIUM HYDROXIDE is a very finely grounded product having an extremely uniform and narrow particle size distribution. View product → |




